ASTM C1036 PDF

January 17, 2020   |   by admin

Flat Glass Inspection Criteria per ASTM C – 11/ASTM C Terminology. crush:lightly pitted condition with a dull gray appearance. dig:deep, short. Find the most up-to-date version of ASTM C at Engineering This standard is issued under the fixed designation C ; the number ASTM Standards: 2 cut size, n—glass ordered cut to its final intended size.

Author: Yogis Tujind
Country: Chad
Language: English (Spanish)
Genre: Sex
Published (Last): 16 October 2005
Pages: 103
PDF File Size: 15.29 Mb
ePub File Size: 18.37 Mb
ISBN: 590-6-55012-381-6
Downloads: 23762
Price: Free* [*Free Regsitration Required]
Uploader: Gardazilkree

The values given in parentheses are for information only. Wired glass may contain numerous gaseous inclusions along the wire. C Within the 3. F None allowed Allowed with a minimum separation of mm aastm in. Medium 75 mm 3 in. The values given in parentheses are for information only.

ASTM C – 16 Standard Specification for Flat Glass

Typical minimum adtm for DST is 0. Applications in which functional characteristics are a consideration and blemishes are not a major concern. This standard has been approved for use by agencies of the Department of Defense. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

Production of architectural glass products including coated, heat treated, laminated, and other select glass products. Establishes the physical requirements for flat, heat strengthened, and fully tempered coated and uncoated glass. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

Start with the glass sample parallel with the zebra board identi?

Historical Version s v1036 view previous versions of standard. Glass intended to be used primarily for architectural glazing products including: C — 06 Standard Speci? A number in parentheses indicates the year of last reapproval. Heavy mm 6 in.

  EMOCIONES DESTRUCTIVAS GOLEMAN PDF

Flat Glass Inspection Criteria per ASTM C 1036 – 11/ASTM C 1048-12

Type I which is a transparent flat glass and Type II which is a patterned and wired flat glass. Table 9 does not apply to glass thicker than D For Q1 and Q2 only, the blemish size includes associated distortion see 6. As an alternate method, the thickness may be measured using two bars with? Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

Allowable blemishes per Table 3 PLUS three rejectable asm blemishes Production of architectural glass products including coated, heat treated, laminated, and other select glass products. None allowed Allowed with a minimum separation of mm 48 in.

The difference in length between the two diagonals D1—D2 shall not exceed the limits set forth in Table 2.

Refer to Table 5 for evaluation criteria. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and aztm. NOTE 3—Edges may be supplied or speci? Last previous edition approved in as C — Current edition approved Oct.

The distance from the viewer to glass surface when the blemish is? The allowable blemish sizes listed in Table 3 c1306 associated distortion for Q1 and Q2, but Q3 and Q4 do not include associated distortion.

Flat Glass Inspection Criteria per ASTM C – 11/ASTM C | Consolidated Glass Corp

Check with the manufacturer for more information. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. The minimum separation distance between blemishes is determined by the minimum separation required for the larger of the two blemishes. The allowable blemish asmt listed in Table 9 do not include associated distortion. Production of general use mirrors and other applications.

  ESSENTIAL REVISION NOTES FOR MRCP BY PHILIP A KALRA PDF

Specifies the quality requirements for flat laminated glass consisting of two or more layers of glass bonded with an interlayer material. This specification covers the quality requirements of ashm, transparent, clear, and tinted glass intended to be used primarily for architectural glazing products.

If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. Not allowed Q6 Quality 6 Allowed Allowed with a minimum separation of mm 24 in. Allowable blemishes for glass thicker than E Provided that normally nondetectable blemishes do not form a cluster that is detectable at mm 6 ft. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Light 75 mm 3 in. Allowed with a minimum separation of mm 48 in. The following chart lists the industry standards and specifications that apply to glass used in windows, doors, skylights and architectural glazing applications. This glass is intended to be used primarily for architectural glazing products including: