EICO 1030 PDF

December 31, 2019   |   by admin

I just got a Eico regulated power supply but without the schematic or any doc. The C- and the VAC all work fine, but the high voltage. Was cleaning in the basement a bit this afternoon, and stumbled across the schematic for this old Eico power supply on my work bench that’s. This is a classic filament, bias, and regulated high voltage power supply, great for testing and experimentation with tube equipment such as.

Author: Togore Voodookus
Country: Dominican Republic
Language: English (Spanish)
Genre: Love
Published (Last): 12 July 2008
Pages: 436
PDF File Size: 3.61 Mb
ePub File Size: 2.62 Mb
ISBN: 774-8-56561-826-4
Downloads: 65556
Price: Free* [*Free Regsitration Required]
Uploader: Taujar

If one diode shorts, you still have another one to continue proper operation of the circuit. It looks super clean. One of the cheapest circuit insurance you can buy is to place diodes in series. A special thank you to the ‘new’ guys that helping out. This item is part of the auction: I then followed the cal procedure eio all worked out well. All buyers shall rely solely on their own investigation and inspection of any Goods. Jul 10330, 1. The time now is Prev Group Next Group.

That’s a country of origin you don’t see very often.

eHam.net Classifieds Detail

I opened it up and found the 2 80uf E-Caps were leaking. In many cases, a shorted cheap component such as diode or filter capacitor can ruin a very expensive or sentimental piece of equipment. Unfortunately, this old diode shorted and took the transformer winding with it, thereby ruining the transformer.

  BC169C DATASHEET PDF

Jul 2, 3. No returns or refunds will be permitted, unless authorized by the seller in writing. Search Media New Media. Buyer shall be responsible for the safe and proper removal of any Goods purchased by Buyer.

In addition to stacking the diodes, I installed fuses for each secondary winding. I use my HV power supplies on a daily basis for a number of tasks such as component testing high voltage diodescapacitor reforming, insulation testing, mocking up tube circuits, and many other purposes. All are longtime members that stepped up to the invite to help out by volunteering their time and effort to help the membership experience on TGP stay on the even keel.

Not only that, but you can put current mfg tubes back in the equipment and still use it. Phase Linear …on the bench! MadMan ‘A Disgusting Brony’. They checked right on the money. This website discusses repair of electronic items.

I fused the screen winding with a 62ma slo-blo fuse, which was the smallest that I had available.

Want to phone or mail the auctioneer? All euco is the opinion of the author and not intended as advice. Didn’t even realize I had some NOS spares hidden away all this time. Goods weighing more than pounds must be removed by a qualified, insured rigger. Everything else looked good.

OT: Eico 1030 Power Supply

Enter Keywords used in Search: We’ve added some “new” guys to the moderator crew. The bias supply 6X4 is a half-wave circuit, so I used two in series. Yes, my password is: Cleaned all the pots and the meter slide switch.

  LINKSYS WAG160N MANUALE PDF

The tubes in such equipment are usually high quality, and are usually operated well within their ratings so they stand a good chance of having life left in them.

I completely forgot that this 0130 was tube driven. The volt meter is very accurate when eifo to my DVM! I replaced the rectifier tubes with fresh silicon ultra-fast diodes because I wanted to reduce the heat inside the cabinet, promote stability, and reduce transformer load 2. Jul 2, 2. For the price of a quality ultrafast diode from a reputable supplier — approx cents each for a Fairchild UF 1A, v — this protection is a bargain. Very spiffy job on the recap.

NEW EICO Regulated Power Supply INSTRUCTION MANUAL – $ | PicClick

Getting notified via SMS Text Message will require you to verify your cell phone via the profile page in your account. Where I could, I went up in wattage. Your eivo or email address: MKBJul 3, I installed an ICL to limit inrush current at power-on. They all checked in the good range. We do not provide free personalized troubleshooting.

About half of the resistors were out of tolerance so I changed them all. I checked all the tubes.